MKN Induction Cooking Table 1223103 – 4 Zone, CounterSL
CounterSL induction cooking table 1223103, 800 x 700 x 270 mm with 14 kW at 400 V and a 700 x 540 mm glass-ceramic work surface.
FlexiCombi electric combi steamer FKECOD115CG2, 10 x GN 1/1 or 10 FlexiRack (≈17x GN 1/1), 15.9 kW, 400 V, for 80–150 meals/day.
| Manufacturer | MKN |
|---|---|
| Article number | FKECOD115CG2 |
| Series | FlexiCombi |
| Dimensions (LxWxH) | 997 x 799 x 1060 mm |
| Net weight | 145 kg |
Ten GN 1/1 levels carrying up to 90 kg of food set the FKECOD115CG2 in the mid-size FlexiCombi class. With a stated throughput of 80–150 meals per day on 1/1 GN, it sits squarely in the volume band of a main galley on a smaller vessel or a dedicated section on a larger ship.
At 997 x 799 x 1060 mm, this oven needs to be planned as a full-width piece of cooking equipment on the line rather than a compact counter unit. The 145 kg net weight and 15.9 kW electrical rating matter directly to the naval architect: the deck foundation has to carry that static load, and the distribution board has to reserve enough power on the 400 V supply without compromising other galley consumers. In a marine galley where heat and humidity feed into the HVAC load, centralising 80–150 meals per day into a single 15.9 kW combi simplifies both extraction and chilled-water calculations compared with spreading that duty across multiple smaller appliances.
The chamber geometry and loading pattern are where the FlexiCombi concept shows. Ten GN 1/1 shelves allow classic longitudinal loading, but the published FlexiRack capacity of 10 racks (≈ 17 x GN 1/1) means the same footprint can carry crosswise racks for higher tray counts per level. That flexibility is valuable on a vessel where menu cycles change between crew, officers and passengers but equipment positions do not. The 90 kg maximum load weight is a practical upper bound for planning batches of bulk items instead of overfilling and compromising air circulation.
Electrical connection is specified at 400 V with a total electrical power of 15.9 kW, so the unit is intended for a three-phase cooking distribution rather than a light commercial ring. In refit work this often decides whether the combi can replace several legacy appliances on an existing busbar, or whether a new feeder is required. The 997 mm length and 799 mm width should also be read against bulkhead clearances and door widths; moving a 145 kg body through existing passages can be more of a constraint than the final siting.
Build and control
• IP-rated water protection
The IP-rated water protection allows the FKECOD115CG2 to live in a galley where cleaning is done with spray rather than wiping, reducing the risk of moisture ingress during routine wash-downs. That, together with the stainless-steel construction typical of this class, supports compliance with hygiene regimes where equipment is regularly inspected.
This combi is the right choice where a single unit has to carry a consistent 80–150 meals per day with the tray density of 10 GN 1/1 or 10 FlexiRack positions, and where 15.9 kW at 400 V is readily available. It is the wrong choice in a pantry or small mess where service volumes are well below this range and installed electrical power is tight; in those cases a smaller chamber with lower connected load will be easier to accommodate. Ordered under MKN product number FKECOD115CG2.
| Manufacturer | MKN |
|---|---|
| Article number | FKECOD115CG2 |
| Series | FlexiCombi |
| Dimensions (LxWxH) | 997 x 799 x 1060 mm |
| Net weight | 145 kg |
| Max. load weight | 90 kg |
| GN 1/1 capacity | 10; FexiRack: 10 (≈ 17x GN 1/1) |
| Meals per day | 80 - 150 (1/1GN) |
| Voltage | 400 V |
| Electrical power | 15.9 kW |
The FKECOD115CG2 holds 10 GN 1/1 containers, or 10 FlexiRack levels corresponding to approximately 17 x GN 1/1, with a maximum load weight of 90 kg.
The stated output is 80–150 meals per day using 1/1 GN containers, depending on menu and loading pattern.
The combi steamer is rated at 15.9 kW electrical power and is designed for a 400 V supply, so it must be connected to a suitable three-phase distribution.
MKN Maschinenfabrik Kurt Neubauer GmbH & Co. KG — German manufacturer of thermal professional cooking technology, supplying marine and aviation galleys for over 75 years. Configured to order — tell us the vessel and the supply voltage and frequency, and we will quote the correct build.
All MKN equipmentDocuments are published by the manufacturer for the standard model. We confirm the build, supply and installation details for your vessel with the quotation.
CounterSL induction cooking table 1223103, 800 x 700 x 270 mm with 14 kW at 400 V and a 700 x 540 mm glass-ceramic work surface.
60-litre round electric boiling kettle with VAPRO steam generator, 16 kW at 400 V in an 800 x 700 mm Optima 700 body. Article 2122802C.
4-zone 20 kW induction top, 1000 x 900 mm, one-side operated thermaline 90 module, 440 V/3 ph/60 Hz, IPX6 washdown-ready.
iVario Pro L multifunctional cooking system in MarineLine marine version: 100 litres, 100–300 meals a day, 27 kW. Boils, fries and deep-fries; DNV GL certified.
Add it to your quote basket with anything else you need, or request a quotation for this item alone.
MKN Combi Steamer FKECOD115CG2 – Oven, Electric, FlexiCombi